Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli Your SEO optimized title Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli – SHOPPERS SHOP
Menu
Cart 0

Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 40CH 600mW VTX 700TVL Cam

Banggood

  • $15999


Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 40CH 600mW VTX 700TVL Cam
 
Eachine Tyro99 210mm DIY Version FPV Racing RC Drone w/ F4 OSD 30A BLHeli_S 700TVL Camera 5.8G 40CH 600mW VTX

Note:
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.

 
Item Specification
210mm Frame Kit

Wheel base: 210mm
Frame arm thickness: 5mm
Bottom plate thickness: 2mm
Side plate thickness: 2mm
Frame kit material: 3K carbon fiber & 6065 aluminium 
 
2206 2150KV Brushless Motor

Motor KV: 2150RPM/V 
Idle current (Io/10V): 1.26A
Lipo cell: 3-5S
Weight: 31g
Max continuous current: 31A
Max continuous power: 496W
Max thrust: 1050g (4S/5")
Configu-ration: 12N/14P
Motor resistance (RM): 0.0572 Ω 
Stator diameter: 22mm
Stator thickness: 6mm
Motor diameter: 27.7mm
Motor body length: 19.2mm
Overall shaft length: 34.2mm
Prop adapter shaft: M5
Bolt holes spacing: 16mm
Bolt thread: M3
Propeller: 5-6 inch
 
4 IN 1 30A BLHeli_S ESC

Continuous current: 30A
Peak Current: 40A(10S)
Input voltage: 2-5S
BEC: 5V 2A BEC
Main control chip: 48Mhz EFM8BB2
Firmware: BLHeli_S supports Dshot600
MOS:  5*6
 
Customized F4 Flight Controller

Main control chip: STM32F405
Sensor: ICM20602 6-axis
Power supply: 5V
Integrated OSD
Onboard LC filter
PID cycle rate & gyro refresh rate up to 32Khz
Supports BetaFlight / inva racing firmware
 
700TVL CMOS Camera

Case size: 25mm*25mm
Weight: 9.5g
Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP)
Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP)
Signal system: PAL/NTSC switchable
Resolution ratio(horizontal center): 700TVL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
White balance: on/off optional 
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: inter-sync
Camera lens: standard 2.8mm
Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
Working current: 70mA (low power consumption)
Working temperature: -20℃~-60℃
Humidity: 0%~98% 
 
5.8G 40CH 0mW/25mw/200mw/600mw switchable VTX

Output power & transmission distance: ≥0.5km@25mW, ≥1km@200mW, ≥2km@600mW
Transmitting power: 0mW/25mW/200mW/600mW
Full video format: NTSC /PAL
Input voltage & power dissipation: 7V~24V, +12V/260mA@600mW
Size: 20*30*9mm
Weight: ≤7g(except antenna)
With output power self-check function.
Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
 
Racerstar 5038 2 Blade Propeller

Material: PC
Mounting hole: 5mm
Center thickness: 8mm
Quantity: 10 pairs
Color: blue, red, yellow, purple, white
Weight: 7.25G a pair   
Delivery color randomly (10 pairs of propellers are the same color)
 
Battery Not included
Recommend 3-5S
Package included:
1 x 210mm frame kit
2 x 2206 2150KV brushless motor CW
2 x  2206 2150KV brushless motor CCW
1 x 
4 IN 1 30A BLHeli_S ESC
1 x 
Customized F4 flight controller
1 x 
700TVL CMOS camera
1 x 5.8G 40CH 0mw/25mw/200mw/600mw switchable VTX
2 x Battery strap
10 x Racerstar 5038 2 blade propeller CW
10 x  Racerstar 5038 2 blade propeller CCW

 
 















We Also Recommend

Sale

Unavailable

Sold Out